Wood finish aluminum extrusion profile , bedroom wardrobe sliding
|Description||Wood finish aluminum extrusion profile , bedroom wardrobe sliding
|Material Thickness(t)||t=1.0 / 1.2 / 1.4|
|Material||Aluminum Alloy 6063, 6061|
|Color||Green, Grey, Black, White, (RAL series)etc.|
Mill finish, anodized, powder coated, electrophoresis,
sand balsting etc.and depend on customer’s demand.
|Shape||Square, Round, Flat, Oval, and according to customer's drawing.|
|Length||Normal length=6m or in customer's order|
Building, Production Line, Decoration, Industrial, Transportation,
Door and window, etc.
1. Pearl cotton foam for each profile;
2. Wrap with shrink film exterior;
3. Packed according to customer request.
Providing colorful products with various mechanical
performances to adapt all kinds of architectural styles
Operation procedure of hot-transfer wood printing process
1: The preparation for production
According to production plan sheet ready already spray or
electrophoresis good base material and the color of the need to
transfer wood grain paper, according to the size of the profile
section will open good required length wood grain paper, the
general scale Zhou Changkuan 3 ~ 5 cm width than the cross section
2: the paper bag
1: The length of the section is 1-2cm, and the paper is laid out.
2: use wood grain paper to wrap the base material that is
reprinted, the interface that USES high temperature glue paper to
hold the paper, in case the paper loosen. (note: on the front of
the reprinted paper, the paper is reprinted on the front of the
reprinted substrate. No wrinkles, no cracks, etc.
3: sets of plastic bags
1: will be the base material of wood grain thermal transfer paper
wrapped over stay high temperature resistance and good sealing tube
plastic bag, by adopting appropriate profile cross section sizes of
high-temperature tubular plastic bag.
2: Note that the plastic glue bag at the end of the bag is reserved
for the length of the plastic bag, which is usually reserved for
15cm in the vacuum end, and 22-25cm on the other side for sealing.
3: When operating, be careful to lightly put, avoid the glue bag to
cut the hole, if there is this image must be repaired.
1: put one end of the bag on the vacuum valve, find the valve,
slowly vacuum, until the plastic bag can be fully and effectively
glued to the substrate. The negative pressure size of the vacuum
should be adjusted according to the characteristics of the
reprinted substrate and the negative pressure of the plastic bag.
2: Arrange the plastic bag flat and open all the vacuum valves.
3: Open the door of the fire door to transfer.
5: Bake the transfer
1: the length of the baking transfer printing temperature and time
should be according to the characteristics of the transfer printing
substrate, to transfer the texture depth and comprehensive factors
such as specific performance of oven do appropriate adjustments,
usually transfer printing temperature is 160 ~ 190 ℃, time of 10 ~
2: During the baking process of the workpiece, observe the
temperature change and ensure the furnace temperature is stable.
3: Check the furnace temperature regularly once a month to
understand the change of the furnace temperature, so as to set up
the best furnace temperature, so as to better make the base
material bake transfer.
6: tear open plastic bags
From the heat transfer in the furnace has been transfer printing
substrate, from one end of the transfer printing substrate was able
to solve the plastic bag, on the other side find some plastic bag
and put away (note: the plastic bag can protect the reuse) should
be paid attention to.
7: tear open paper
Remove the wood grain paper from the printed section. Open one end
and draw the paper from the other end, and then you can use two or
three to increase the speed of the paper.
8: Quality inspection
The surface quality, color and appearance of the finished paper
will be inspected, the workpiece of quality defects will be
selected, and it will be processed in the pending area.
The products inspected and qualified shall be packed in accordance
with the requirements or plans of the contract.